Ghost For Glock Magazine Extension +6 For 19 23 26 27 32 33 MOAB GEN 1-5

Description

Ghost Glock MOAB Mother of all Base plates Magazine
Extension
Black
Plus 6 Rounds for 9mm
NOT COMPATIBLE WITH EARLY GEN 1 PARTIAL-METAL LINED MAGAZINES.
Fits Glock OEM Standard
Capacity
Mags for the listed models only
FITS Glock Models 19 23 26 27 32 33
Will not fit Glock models 42 or 43 43X 48
PLEASE NOTE WILL NOT WORK ON 10 ROUND MAGS
BUY WITH CONFIDENCE WE ARE AN AUTHORIZED GHOST TOP DEALER!
Features:
Features:
Adds 6 Rounds to Glock's Magazines!
Works on 19, 23 26, 32 and 33 magazines
Stainless steel extra power magazine spring included
Rounded ergo design
Positive mag seating
Extraction Traction Points
Debris extraction ports
Superior tough construction
No more painful corner spikes in your palm
Ghost unconditional lifetime warranty!
This is by far the toughest and best looking Plus 6 Glock magazine extension yet !
Extremely tough, it's been rumored to have been used as an impact weapon.
Perfect for all of the following Glocks
Gens 1-5
Models 19 23 26 27 32 33
Add 6 rounds
100% Satisfaction guarantee with an unconditional lifetime warranty.
These patent pending Ghost Base plates have a rounded design that insures proper seating of your magazine without hurting your hand!
Use of OEM base pad can ruin your day! It's undersized, has no gripping surfaces and is flat! Extraction becomes difficult should your magazine fail to drop free.
The Ghost MOAB's are flared, with finger grooves providing non-slip scallops for positive finger purchase. Stubborn or stuck mags are easily extracted.
We also added two debris evacuation ports. Fact: When you drop magazines, debris enters. We have designed the ports to evacuate debris, including water, dirt and other matter. Additionally, on of the Debris Evacuation Ports can also serve as a through-point for a lanyard or pull tab.
Attractive dimpled features on the bottom provide ample options for labeling your magazines.
Installation Instructions:
The Ghost MOAB magazine extension for Glock factory magazines consists of 4 items 3 of which make up the magazine extension assembly;
The Sleeve-the rectangular piece that you may look through
-
Assembly
The MOAB Spring-the coil stainless steel spring that powers the extension
-Assembly
The MOAB Base-the MOAB that inserts into the sleeve
-Assembly
The Disassembly Tool-if ever needed to disassemble the assembly.
Prior to installation of
Ghost MOAB magazine extension
, you must remove the (1) existing magazine base plate (2) magazine base plate insert, (3) the magazine spring and (4) remove the follower from the spring, you will reuse only (4) the
follower
. Place the unused parts in suitable storage container and label them for possible future use-
Caution the contents are under the pressure of the magazine spring, eye protection must be worn when manipulating springs.
Note: Once removed you may want to consider cleaning the magazine body.
Slide the Sleeve part number one (1) with the shortest side oriented along the rear of the magazine until it can go no further.
Attach the spring into the follower you removed from the host magazine. You will notice that the spring is not symmetrical there is a large end (bottom) and a small end (top). This small end snaps into the follower (if it does not completely snap in you may still install the follower partially on the spring after a loading it will seat onto the spring). Now with the follower attached to the spring insert them all into the magazine until you see the follower is at the limit of it’s travel in the magazine. There will be many coils extending below the sleeve.
Grip the magazine body firmly so that you can push down on the installed MOAB Sleeve (1) towards the bottom of the magazine. This downward pressure will aid in locking the MOAB Base (3) into the sleeve when you join them.
With the MOAB Base (3) use it to capture the large end or bottom of the spring.
Push the MOAB Base (3) with the MOAB spring (2) into the MOAB Sleeve (1) until it locks, it should make snapping sound-you’re done!
To remove reverse the process. To remove the base, you will need the tool and a pair of pliers or channel locks to compress the disassembly tool enough to unlock the base. We designed these to stay on!!